Skip to main content

Install Guide

How to Install Rock Lights on a Truck or Rig

Step-by-step guide to mounting and wiring rock lights on a truck, Jeep, or trail rig. Pick the right spots, run clean wire, and flip the switch.

Shop rock lights

What Are Rock Lights and Why Bother Installing Them?

Rock lights are small, rugged LED pods mounted under the frame, rocker panels, and axles of a truck, Jeep, UTV, or trail rig. They throw light down and outward so you can see the terrain under your rig at night. That matters a lot when you are picking a line through a rocky wash or crawling a ledge in the dark and you need to see exactly where your tires are sitting.

Beyond the practical side, rock lights are one of the most popular ways to give a build a finished, aggressive look. A set of color-changing pods glowing under a lifted truck at a show or a trail meetup is hard to miss. Either way, the install is something most people can do in an afternoon with basic hand tools. This guide walks you through the whole process from planning to flipping the switch.

One thing to know up front: many rock lights are sold as off-road use only. Lighting laws vary by state, and some colors (red, blue, and flashing patterns in particular) are restricted or outright illegal on public roads in most places. Check your local laws before you drive on the street with them on. Our guide on off-road lighting laws covers this in more detail.

Plan Your Layout Before You Buy Anything

The number of lights you need depends on the size of your rig and what you want to cover. A short-wheelbase Jeep can look great with four to six pods. A long-bed truck or a side-by-side with wide bodywork might want eight or more to get even coverage from front to back. Think about where the shadows fall when you park on a dark trail and work from there.

Common mounting spots are along the rocker panels, on the front and rear axle housings, inside the wheel wells, and on the frame rails near the bumpers. Rocker-panel placement gives you the widest spread of light across the ground. Axle-mounted lights point straight down and help you watch tire placement on obstacles. You do not have to pick just one zone, and most kits are designed to cover all of them.

Also decide now whether you want a single color, a multi-color RGB setup, or color-changing pods with a controller. Single-color installs are simpler to wire. RGB kits add a controller and sometimes a Bluetooth app. Either way, the physical mounting process is the same. If you are still deciding on the right kit, our guide on how to choose rock lights for your truck walks through the options in detail.

Not sure how many pods your specific rig needs? Check out our guide on how many rock lights you need before you order.

Tools and Parts You Need Before You Start

Getting everything together before you crawl under the truck saves a lot of back-and-forth. The list is not long, but missing one item mid-install is frustrating.

Here is what you will need for a typical rock light install:

  • Rock light kit (pods, mounting hardware, and pigtail leads included with most kits)
  • Wiring harness with relay and inline fuse, sized for the number of pods you are running
  • A switch or switch panel to control the lights from the cab
  • Drill and drill bits (step bit recommended for clean holes through sheet metal)
  • Socket set and wrenches
  • Wire stripper and crimping tool
  • Heat-shrink connectors or butt connectors and a heat gun
  • Zip ties and split loom or wire loom to protect and bundle the wire runs
  • Dielectric grease for all exposed connections
  • Marker or paint pen to mark hole locations
  • Flashlight or a work light to see up into the frame rails

Step-by-Step: How to Mount and Wire Rock Lights

Follow these steps in order. The physical mounting comes first, then the wiring runs, then the power connection. Doing it in this sequence means you are not pulling wire through tight spots twice.

Take your time on the wire routing. Sloppy wire runs are the number one reason rock lights fail early. A wire that rubs against a sharp frame edge or gets pinched by a suspension component will eventually cut through and short out. Protect every inch of wire that runs near heat, sharp edges, or moving parts.

Once everything is connected, test the lights before you button up the zip ties and close the loom. It is much easier to chase a bad connection now than after everything is neatly bundled and tucked away.

Wiring It Right: Harness, Relay, and Switch

Most rock light kits come with short pigtail leads on each pod. Those pigtails need to connect to a main harness that runs back to your power source. Do not wire rock lights directly to your battery without a relay and an inline fuse. The relay protects your switch and keeps the current load off the switch itself. The fuse protects the whole circuit if something shorts.

A quality wiring harness sized for your pod count makes this straightforward. The harness has a relay, an inline fuse, a trigger wire that runs to your switch, and a main power lead that goes to the battery. Each pod pigtail connects to the harness output. Many harnesses use weatherproof connectors so you are not making bare wire splices under the rig where moisture and mud will find them.

Run the trigger wire from the harness through a firewall grommet into the cab and connect it to your switch. Mount the switch somewhere you can reach it easily. A rocker switch panel on the dash or A-pillar is a common choice. If you are running RGB lights, the controller usually sits in the cab as well and the trigger wire goes to it instead. Browse our power harnesses and our switches to find options that match your setup.

Seal every connection you make under the rig with dielectric grease and heat-shrink tubing. Bare crimp connectors will corrode fast when they are exposed to water, mud, and road grime. A connection that looks fine in the driveway can fail on the trail after the first water crossing.

Common Mistakes and How to Avoid Them

The most common mistake is mounting pods in spots that look good in the driveway but get destroyed on the trail. Anything hanging below the frame rail is going to take hits. Anything mounted directly to the axle housing needs to be small and tight so it does not snag on rocks. Think about your rig's ground clearance and how low you actually wheel before you commit to a mounting location.

The second most common mistake is running wire without protection. Split loom or corrugated wire loom is cheap and it keeps your wiring from getting chewed up. Any wire that passes through a hole in sheet metal needs a rubber grommet so the metal edge does not cut through the insulation over time. Any wire near the exhaust needs to be rerouted or sleeved with heat-resistant material.

Finally, do not skip the relay. Running a high-current load directly through a small toggle switch is a fire risk and will burn out the switch. The relay does the heavy lifting. The switch just tells the relay when to open and close. It is a simple addition that makes the whole install safe and reliable.

  • Mount pods above or flush with the lowest frame point whenever possible
  • Use grommets at every hole where wire passes through metal
  • Keep wire runs away from the exhaust, driveshaft, and suspension pivot points
  • Always use a relay and inline fuse on the main power circuit
  • Seal every connection with dielectric grease and heat-shrink tubing
  • Test before you button everything up with zip ties

What to Do After the Install

Once the lights are on and tested, go back and tighten every mounting fastener. Vibration on the trail will loosen hardware that felt snug in the driveway. A dab of thread-locking compound on the pod mounting bolts is a good idea if your rig sees rough terrain regularly.

Do a full inspection after your first trail run. Look for wire rub points you missed, pods that shifted, or connections that got wet. The first run is the best time to catch problems before they turn into failures. After that, a quick check every few trail runs keeps everything in good shape.

If you want to expand the setup later, adding more pods to an existing harness is usually straightforward as long as the harness has enough capacity. Check the harness specs before you add pods. If you are maxing it out, a second harness run in parallel is cleaner than overloading the first one.

Step by step

  1. 1

    Plan your mounting locations

    Crawl under the rig and mark where each pod will go. Focus on rocker panels, frame rails, and axle housings. Make sure every location clears your suspension travel and sits above the lowest point of the frame so pods do not take direct rock hits.

  2. 2

    Mount the pods

    Drill or tap holes at each marked location and secure the pods using the hardware included with your kit. Install a rubber grommet anywhere a wire will pass through a hole in sheet metal. Snug the fasteners down but do not fully torque them until after you have tested the lights.

  3. 3

    Route the wiring harness

    Run the main harness along the frame rail from the battery area toward the rear of the rig. Keep the wire away from the exhaust, driveshaft, and any suspension pivot points. Use zip ties to hold the harness against the frame every several inches so it cannot sag or swing.

  4. 4

    Connect the pod pigtails to the harness

    Plug each pod's pigtail lead into the corresponding harness connector. If your kit uses bare wire connections instead of weatherproof plugs, crimp the joints with waterproof butt connectors, apply dielectric grease, and seal with heat-shrink tubing.

  5. 5

    Protect all wire runs

    Sleeve every exposed wire run with split loom or corrugated wire loom. Pay extra attention to any section that runs near heat sources or through tight areas where the wire could rub against metal edges.

  6. 6

    Run the trigger wire into the cab and connect the switch

    Feed the relay trigger wire through an existing firewall grommet into the cab. Connect it to your switch or switch panel. Mount the switch in a location you can reach easily from the driver seat.

  7. 7

    Connect the main power lead to the battery

    Connect the harness power lead to the positive battery terminal and the ground lead to a clean chassis ground point. Make sure the inline fuse is in place before making the final connection.

  8. 8

    Test the lights and finalize the install

    Turn on the switch and confirm all pods light up. Check for any pods that are dim or not working and trace the connection. Once everything checks out, tighten all mounting hardware, close up the wire loom, and secure any loose wire runs with additional zip ties.

Quick answers

Can I install rock lights without drilling into my frame or body?

Yes, in many cases. A lot of rock lights mount with self-tapping screws into existing holes, clamp onto frame rails, or use adhesive-backed brackets for flat surfaces. That said, drilling gives you the most secure mount, especially if you wheel hard. If you go the no-drill route, make sure the mounting method is rated for off-road vibration and that the pods are positioned where they will not take direct rock hits.

How do I connect rock lights to a switch inside the cab?

The cleanest way is to run the trigger wire from your relay harness through an existing firewall grommet into the cab, then connect it to a rocker switch or switch panel mounted on the dash or A-pillar. The switch completes the circuit to the relay, which then powers the lights. You do not want to run the full current load through the switch itself, just the trigger signal. That is why the relay is so important. Our wiring guide on how to wire rock lights to a switch covers this in more detail.

Are rock lights waterproof enough for water crossings?

Most quality rock lights carry an IP67 or IP68 waterproof rating, which means they can handle submersion for a defined period at a defined depth. That is generally enough for trail water crossings. The pods themselves are usually fine. The weak points are the wire connections and the harness connectors. Use weatherproof connectors, seal every splice with heat-shrink and dielectric grease, and route the harness so standing water does not pool around connections. Check the IP rating on any pods you are considering before you buy.

How many rock lights do I need for a full-size truck?

A full-size truck typically looks best and gets good coverage with eight pods, two per corner or two per rocker section front and rear. Some builders run more if they want to cover the axles as well. Six is workable if you space them evenly. Four will leave gaps on a long wheelbase. The goal is even light spread across the ground under the rig with no dark patches between pods.

Can I run rock lights on a UTV or side-by-side the same way?

The process is very similar. UTVs and side-by-sides have shorter frame rails and less total length to cover, so you often need fewer pods. The wiring and relay setup is the same. The main difference is that UTV frames can have less room to tuck wire runs, so plan your routing carefully. Our guide on how to install pod lights on a UTV has tips that apply to rock lights on UTVs as well.

Next steps